Site Information

 Loading... Please wait...
  • Image 1
  • Image 2

Kenton Pro Solo MkII High specification single synth MIDI to CV converter

$239.00
SKU:
rev-496917
Availability:
ended

Out of Stock

Product Description

Power: 9V DC (regulated or unregulated) – never apply more than 12V (never use an unregulated supply greater than 9V as unregulated supplies typically give a higher output than shown). 9V switch mode power supply included. USA power supply. Dimensions: 130 x 97 x 40 mm Weight: 450g MIDI: In, Thru (selectable) Analogue Outputs: CV on 3.5mm jack (V/oct or Hz/V)
Gate on 3.5mm jack (Gate or S-trig)
Aux on 3.5 mm jack Digital Outputs: Pins 1 & 3 of Thru socket (if selected) off=0 volts on=5 volts       Please refer to the manual for more details

  • Designed to control all types of mono-synth
  • Super-fast response time
  • Famous Kenton build quality
  • Rugged steel case
  • High specification 16 bit D/A converters for rock-steady pitches
  • Runs from standard 9 volt power supply, 2.1mm centre positive
  • CV/Gate/Aux1 outputs on 3.5mm jack sockets (3.5mm to 1/4" cables are available in our cables section)
  • MIDI IN socket
  • MIDI THRU socket can be switched to become DIN SYNC or AUX 2 & 3
  • Any MIDI channel can be selected
  • Switchable for V/oct & Hz/V & 1.2V/oct scaling systems
  • Fine tune & scale are software controllable
  • Transpose (coarse tune) - up & down 12 semitones
  • Adjustable pitchbend range
  • Programmable Gate V-trig (up to 15v) or S-trig (with or without pull-up)
  • Multiple and single trigger modes
  • Note priority selection - newest / lowest / highest
  • Old notes are remembered to facilitate trill effects and increase playability
  • Portamento - fixed rate or fixed time modes
  • Auto Portamento mode selectable (where legato playing turns on Portamento)
  • Portamento Controller is selectable
  • Programmable AUX 1 variable analogue output controllable by any MIDI controller
  • AUX 2 & 3 (if selected) are switch outputs giving +5V or zero, depending on controller value
  • Programmable LFO - 9 wave shapes inc. random
  • LFO can modulate pitch &/or AUX output
  • Separate Controllers for LFO to CV and LFO to AUX
  • LFO can be synchronised to MIDI clock
  • LFO sync point can be selected
  • Key-on can reset LFO
  • Aux1 output can output clock
  • Clock output can select from 1 to 12, 24, or 48 clocks per quarter note
  • All parameters are controllable in real-time by SysEx
  • Set-up are stored in non-volatile memory for easy recall
  • MIDI monitor mode - for easy MIDI troubleshooting
  • Power supply included - USA

What's new or different about the MkII?

  • Now runs from standard 9 volt power supply - centre positive
  • MIDI THRU socket can be switched to become DIN SYNC or AUX 2 & 3
  • Portamento - new fixed time mode as well as existing fixed rate
  • Auto Portamento mode selectable (where legato playing turns on Portamento)
  • LFO sync point can be selected
  • LFO to CV controller now has Min, Max and Reset values
  • LFO to Aux controller now has Min, Max and Reset values
  • Key-on can reset LFO
  • All parameters are controllable in real-time by SysEx
  • Aux1 output can output clock at 1 to 12, 24, or 48 clocks per quarter note
  • Din sync and clock can be used at the same time as CV and Gate outputs
  • Can control all 5 connections of a TB-303 5 Socket upgrade at the same time
  • Display now uses all three digits to display numbers
  • Box now an attractive cobalt blue colour

 

Note 1 - A power supply (wall wart) is now included with this product . Four types are available, UK / EU / USA / Australian. We will automatically supply the correct type for your country.

Note 2 - whereas Aux1 is continuously variable and can be controlled from a wide variety of sources, Auxes 2 & 3 can output only 0 or 5 volts (split at data value 64) and can only be controlled by continuous controllers (CCs). When Aux 2/3 mode is selected, the thru socket pins 1 and 3 become auxes 2 & 3. You will need a 5 pin Din to 2 jacks cable to make use of Auxes 2 & 3. This mode was introduced mainly for the Accent and Slide inputs of our 5 Socket upgrade for the TB-303, allowing the Pro-SOLO mkII to control all 5 inputs at the same time.

Product Reviews

Write Review

This product hasn't received any reviews yet. Be the first to review this product!

Find Similar Products by Category

Click the button below to add the Kenton Pro Solo MkII High specification single synth MIDI to CV converter to your wish list.